If you want to access the Deep Lake weather and webcams you can go to www.deeplakewa.com and you will have all of the same information and probably a little bit more than what you had when those pages were hosted here.  Couple of side notes… Pan and Tilt is back and while performance depends on the satellite internet it is functioning pretty well.  You can get the weather emailed to you by signing up for the mailing list.  

 

The holiday brought us a lot of snow!!!

I thought I would attach a few pictures to this post to give you an idea of just how much snow we are dealing with.

As a new “front” comes in tonight we are expecting to get another 10-12 inches and of course there is no end in site.

You can check on the webcam periodically to see the progress.  Notice that the benches around the fire pit are no longer visible.  You also can’t seem

much of the bench that is normally in front of the spruce tree.  We did put lights in the spruce again this year but thee is so much snow on the tree that they are hard to see. 

I’m ready for some global warming.

You can also see the last 40 webcam images here…

Initially, installation was a bit troublesome for me…  The camera that I purchased had a lower version of software included in the box and I could not get it to function over the Internet.   I quickly contacted tech support and within just a few hours I had upgraded to version 3 of the software and things began to work as I had hoped and planned.

The version of the camera that I have does require not only a USB connection but also a serial connection to your PC.  There are versions of the camera that function solely on a USB connection.  They also offer as an accessory an extension cables that allows you to extend the standard 9 foot cable for those difficult and hard to reach camera placements.  For now, I just installed it in my office window.  I didn’t need the extension.

If you have an Internet connection that uses a router you will need to “open” the necessary port to allow for the UDP traffic from the Internet to reach the PC where the camera was attached.  A typical installation would be to open the port that is 7000 + the last octet of the PC’s IP address.  (DHCP could be problematic because you would not know which IP address to redirect the traffic to.)  In my setup I just changed the PC to have a static IP of 10.1.1.99 and then I opened port 7099 to forward to that IP address. 

A quick installation would include:

1. Create an account at the mcam website.  (This is used to direct people to your camera) 
2. Configure your PC’s IP address and your router’s port forwarding to that IP.
3. Install the software (version 3) – It is going to ask you for your mcam login information.
4. Attach the camera and allow the drivers to be found by Windows,  then perform a reboot.
5. Configure the camera as you would like in the server software.  You can include time, some camera setup options, etc.
6. Link to the camera from your web page (if you want others to see it) or simply save the address as a bookmark for your own private use.

So far I am quite happy with the installation…  If you would like to try it out, there is a demonstration camera on their website.   You can also find additional tech information here.  If you have an interest in Deep Lake and would like to be able to control the camera up there leave me a comment on the Deep Lake page.

My solution…Create a batch file and put it into my STARTUP folder that runs the programs I want to run in the order and with the timing that I want them to run.

Relatively simple solution.   I created a file with an editor called WebCam.BAT in the All User/Programs/Startup folder.   The basics of this file are:

@ECHO OFF  

ECHO Pausing to wait for Windows to get through standard startup routines...

PING -n91 127.0.0.1>nul

START \"PanTilt\" /B \"C:\path to MCAM software\"

Ping -n61 127.0.0.1>nul

START \"WEBCAM\" /B \"C:\path to webcam capture\"

That’s really it.  Since I needed to have a delay and there isn’t a Pause for XX seconds command for batch files I “cheat” and  just tell it to PING my local machine a sufficient number of times to get the delay I want and send the output of the ping command to nowhere.  You can also find more information on the START command here…

While this still isn’t the Canon camera that I want (check out the Old Faithful streaming webcam found in this post) we are going to experiment to see just how much use it will get.  Keep in mind I have a satellite connection with limited bandwidth so public usage of this camera will be restricted.   Those with a specific interest in Deep Lake will certainly be able to receive the password that will control the movement of the camera via the Internet.

Welcome to Projects Possible…

So how in the world did you get here?  You thought you were going to the Deep Lake Webcam, or perhaps even bigbrofan.com and somehow you ended up here.   Through the magic of the Internet most of my personal Web pages have been redirected to here. In cases where I have decided to continue with the content or subject matter you may have been directed to specific posts or pages here on Projects Possible… my new blog.

You can expect to find some of the familiar content of my other pages and a bit more.   The goal is to provide an enjoyable and entertaining read where you can interact and comment and share some of your own thoughts on the varied topics that I will be found.

If you thought you were going to find a Web Page for a ski area in Spain you must have tried going to masella.com.   Masella is a family name and while I tried to register it, the ski area registered masella.com before I did.  I do have masella.us, and going to that domain will bring you here as well.  Two names, same great place.

What about bigbrofan.com?  The fan site for Big Brother Australia is no longer being supported or maintained.  I still own the domain and I may actually put some of the content into a page here if someone wants it.   Keep in mind I did not watch last season at all so any and all media I have would be from seasons 1-6.   If this is something you want or are looking for, leave a comment and I will see what I can do to perhaps accomodate that request.  In the meantime enjoy some of the new content.

The domains deeplakewa.com and grizzlyway.com are both for the webcams and weather station that are located at our home on Deep Lake.  These two domains will link directly to the Deep Lake page here on the blog so feel free to continue using them if you are not interested in the other content here at Projects Possible!

I own a number of other domains that may also eventually be directed to the blog.  

As I’ve said, I encourage your comments and discussion.  Feel free to use my permalinks in your posts and have a great time as you wade through the varied content of Projects Possible!